In some cases you must enter a second code (50 digits higher) to stop the test. Some require a second press of the “Start” button to stop the test. Then press "Start." This will test the component. Enter the number of the code, using the number keys. Hold down 0 & 3 keys while turning on power. This group is done with fax button on and fax LED on.ģ: G: Bridge unit paper full sensor, job separator lower stack sensor or offset stack sensorģ: H: Bridge transport sensor, job separator feed sensor or offset tray sensor.Ħ: D, E, F, G, G: APS sensors R, C, 3, 2, 1ĩ: A: Bridge/job separator/offset tray connected1ĩ: B: Bridge/job separator/offset tray connected2ĩ: C: Bridge/job separator/offset tray connected3Ġ: A: Dongle (that’s what it says!) for GM-2010Ġ: D: Dongle for other USB devices and other equipmentĠ & 3 Mode-outputs: Shut power. This group is done with fax button off and fax LED off.Ģ: C: PFP upper drawer paper stock sensor You will press the indicated key to test the item listed. There are “buttons” A, B, C, D, E, F, G, H that will display. Inputs: These are signals that enter the main board, and are supplied by switches and sensors throughout the machine.Ġ & 1 Mode: Lights operation panel display.Ġ & 3 Mode: These are signals that enter the main board, and are supplied by switches and sensors throughout the machine. SIMULATIONS: Hold down the two keys (0 and 1 for example) while turning on power. Press “Start.” Change status to “0.” Press "ENTER" or "INTERRUPT." Shut power and turn back on.Ĭ550: Communication problem between IF and RADF.Ĭ570: Communication problem between engine-CPU and IPC.Ĭ580: Communication problem between IPC and finisher.Ĭ730: EEPROM initialization problem in RADF.Ĭ830: Original length sensor adjustment error.ĬA10: Laser motor (polygon motor) problem.ĬB90: Finisher paper push plate motor CB7: Finisher height sensor.ĬBA0: Saddle stitcher front stitcher motor.ĬBB0: Saddle stitcher rear stitcher motor.ĬBF0: Saddle stitcher paper positioning plate motor.ĬC20: Saddle stitcher to finisher communications problem.ĬC50: Finisher horizontal registration motor.ĬC90: Finisher upper stack tray lift motor.ĬCA0: Finisher lower stack tray lift motor.ĬCE0: Finisher paper trail edge assist motor.ĬDF0: Offset tray home separator problem.ĬE00: Communication problem between finisher and punch.Į300, 310, 320: PFP upper drawer transport jam.Į330, 340, 350, 360: PFP lower drawer transport jam.ĮA10, EA20, EA30, EA40, EA50, EA60, EA70: Finisher jams.ĮA80, EA90, EAA0, EAB0 EAC0, EAD0, EAE0, EAF0: Saddle-stitch finisher jams.į070: Communication error between system-CPPU and engine-CPU.į092: SRAM and NVRAM problem on SYS board.į110: Communication error between system-CPU and scan-CPU. To clear fuser errors turn on power while holding down “0” & “8.” Enter 400. All codes, except fuser errors, are reset by turning the machine off and back on again.Ĭ470: IH initialization power voltage. To read them, press down the "8" key and the “Clear/Stop” key at the same time. If the machine has a jam ("Clear paper") or "picture of a wrench" you can read these codes.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |